To replace windows in Fort Lauderdale, measure each opening, pick HVHZ impact products and get the Miami-Dade Notice of Acceptance from the seller, fill out the Broward Uniform Retrofit Window & Door Schedule, get HOA, condo or historic approval, apply online through LauderBuild, record the Notice of Commencement, pass inspections, then book a wind mitigation inspection.
Last checked: October 24, 2026 · General guidance. Confirm requirements for your address with the Fort Lauderdale building department.
Fort Lauderdale is a paperless permit city
The first thing to know: since January 1, 2024, the City of Fort Lauderdale does not take paper permit applications or paper plans for new submissions. Every window and door permit goes through LauderBuild, the city's online portal at aca3.accela.com/FTL, and plans are reviewed in the LauderBuild Plan Room.
Permits come from the city's Development Services Department (DSD), whose Building Services division also performs the inspections.
Confirm your home is inside city limits first. Some "Fort Lauderdale" mailing ZIP codes reach into neighboring cities, and the permit office depends on the property's actual city, not the ZIP.
Why a Fort Lauderdale window has to pass a tougher test
Fort Lauderdale is in Broward County. Broward and Miami-Dade together make up the High-Velocity Hurricane Zone (HVHZ) of the Florida Building Code. Palm Beach County is not held to HVHZ rules, so a window that is fine a short drive north may not be allowed here.
The zone traces back to Hurricane Andrew: the 1994 South Florida Building Code created the HVHZ idea, and a statewide code later replaced more than 400 local ones.
For a typical home (Risk Category II), the code sets Broward's design wind speed at 170 mph as a 3-second gust. Each window then needs a design pressure rating that covers its size and its spot on the wall. The city's checklist says windows and doors must be impact resistant unless they are protected by shutters.
- Product approval: the city's Windows and Doors Permit Checklist asks for a copy of the Miami-Dade County Notice of Acceptance (NOA) for each product, obtained from where you buy it.
- Code edition: Broward's current retrofit rules are written for the Florida Building Code 8th Edition (2023). The 9th Edition is scheduled to take effect December 31, 2026, and permits applied for after that date may fall under the new edition.
What Wilma and Irma showed in Fort Lauderdale
Hurricane Wilma came ashore on the southwest coast in October 2005, yet the National Weather Service recorded a 99 mph peak gust (preliminary) at Fort Lauderdale, and news reports described downtown high-rise windows blown out.
In 2017, Irma brought an 87 mph gust at Port Everglades and beachfront flooding reaching Fort Lauderdale. A storm does not need a direct hit to test your windows.
Which Fort Lauderdale home are you working on?
The steps change with the building. Fort Lauderdale is a mix: about a third of its housing units are single-family houses, while about 40% sit in buildings with 20 or more units. The median home was built in 1973, and about 60% of units date from 1950 to 1979, long before the HVHZ existed.
| Home type | Share of units | What it means for your project |
|---|---|---|
| Single-family detached house | 32.9% | Mostly older homes; measure the rough opening, not the old window. |
| Townhouse (single-family attached) | 5.9% | Covered by the Broward retrofit rules for low-rise homes. Check HOA rules on frame color and style. |
| Building with 20+ units | 40.2% | Condo association approval comes first. Buildings 30 feet or taller need an engineer's site-specific design. |
| Building with 50+ units (part of the 20+ group) | 30.1% | Expect association specs and engineer-sealed pressures for every opening. |
Step by step: replacing windows in Fort Lauderdale
- 1. Confirm the city and the zone. Check that the property is inside Fort Lauderdale city limits. Look up your flood zone on the city's flood map page.
- 2. Measure every opening. Measure the rough opening width and height for each window and door, and number each one on a simple floor plan. On a 1960s or 1970s house, measure at three points each way, because older openings are often not square.
- 3. Choose products with the right approval. Pick impact windows and doors approved for the HVHZ. Get the Miami-Dade NOA for each product from the seller. The approval must cover the size and design pressure of each opening.
- 4. Find your design pressures. For a house or townhouse with a roof height under 30 feet, Broward's rules allow pressures from a sealed site plan, a sealed worst-case chart, or the Broward County Fenestration Voluntary Wind Load Chart. For buildings 30 feet or taller, a Florida engineer or architect must seal a site-specific design for every opening.
- 5. Fill out the retrofit schedule. Fort Lauderdale requires the Broward County Uniform Retrofit Window & Door Schedule (BORA Policy 20-01). It lists each opening's location, product approval number, approved rating, required design pressure, size, impact glass or shutter, and mullions.
- 6. Get association or historic approval. If you have an HOA or condo association, get its written approval. In a historic district, get a Certificate of Appropriateness before the building permit (see below).
- 7. Apply on LauderBuild. Sign in or register at aca3.accela.com/FTL, then choose Apply > Permits/Engineering (ROW). Upload the schedule, product approvals and any engineering.
- 8. Record the Notice of Commencement. If the direct contract is more than $5,000, Florida law requires a copy of the recorded Notice of Commencement to be filed with the permit office before the first inspection. Record it with Broward County.
- 9. Installation day. New units go in with the fasteners and buck shown in the product approval. A different buck or fastener needs a signed and sealed letter or drawing from a Florida engineer or architect.
- 10. Inspections and closing the permit. Schedule inspections through DSD Customer Service at 954-828-6520, option 1, Monday to Friday, 8:00 am to 3:30 pm. Ask which inspections your permit needs. The job is done when the final inspection passes and the permit shows as closed in LauderBuild.
- 11. Wind mitigation form. After the permit closes, book a wind mitigation inspection. Form OIR-B1-1802 can document your new opening protection for your insurer.
Sailboat Bend and the other historic districts
Fort Lauderdale has three locally designated historic districts: Sailboat Bend, Himmarshee Street/SW 2nd Avenue, and the Stranahan House district. Sailboat Bend is the largest, with more than 550 buildings in the city's oldest neighborhood, mostly small one-story homes with Bungalow, Mission or Mediterranean Revival details. It is governed by ULDR Section 47-17, and a 2021 survey rated each property Contributing or Non-Contributing.
Any work that changes the outside look of a designated historic property needs a Certificate of Appropriateness (COA).
- Start at the Urban Design and Planning counter, before the building permit.
- Replacements that match existing features can be reviewed by the Historic Preservation Planner without a board hearing.
- Other changes go to the Historic Preservation Board, which meets monthly.
- Once the COA is approved, the project moves to the Building Division for the permit.
Condo towers on the beach and downtown
About 30% of the city's housing is in buildings of 50 or more units, so many projects here are condo units.
- Get the association's written approval and its window spec (frame color, glass tint, style) before you order.
- If the building is 30 feet or taller, Broward rules require a signed and sealed site-specific design showing every retrofit opening and its pressure. Generic charts alone are not accepted.
- Ask the association about milestone inspections. Florida requires them for condo buildings three or more habitable stories tall by the end of the year the building turns 30, and every 10 years after.
Canal and waterfront homes
Fort Lauderdale is called the "Venice of America", with about 165 miles of inland waterways tied to the Intracoastal. Homes in Las Olas Isles, Harbor Beach, Coral Ridge Isles and other canal neighborhoods often sit in or near a flood zone. Coastal high-hazard areas with wave action are mapped as Zone VE.
The city is a Class 7 community in FEMA's Community Rating System, which lowers flood insurance premiums citywide.
One more local rule: under City Code Section 18-9(a), boarding up openings for an emergency is limited to 60 days. Impact glass removes the need to put up and take down shutters at all.
What changes the price of a Fort Lauderdale job
This page does not list prices. For installed prices by size, see Impact Windows Cost in Fort Lauderdale. Here is what moves the number on a Fort Lauderdale project:
- HVHZ approval: every opening needs a product approved for Broward's high-velocity zone at its own design pressure.
- Building height: a condo building 30 feet or taller needs a sealed site-specific design, which adds engineering.
- Size and type: a small bathroom single hung and a wide living-room roller or sliding door are very different products.
- Glass and doors: tint, low-E, an association spec, and each patio or dock door change the total.
- Not included in product prices: city permit fees, sales tax, engineering when required, and Notice of Commencement recording.
Getting help with a Fort Lauderdale project
Vieser Construction is an authorized installer for ESW, Mr. Glass and PGT, with an office at 5121 NE 17th Terrace, Fort Lauderdale. We coordinate your complete installation from measurement to final inspection.
Permit assistance is available. Our team coordinates the complete permitting process, including required documentation, engineering and permit submission, when applicable.
For in-stock projects, materials typically arrive 2–3 weeks after contract. Call or text (754) 707-3281 with your address, your home type (house, townhouse or condo unit) and your opening sizes to start.
Fort Lauderdale window replacement questions
How do I apply for a window permit in Fort Lauderdale?
Online only. Since January 1, 2024, the city no longer accepts paper applications for new submissions. Sign in or register on LauderBuild at aca3.accela.com/FTL, choose Apply > Permits/Engineering (ROW), and upload the Broward Uniform Retrofit Window & Door Schedule and product approvals. DSD's Permit Solutions team can help.
Does Fort Lauderdale require a Miami-Dade NOA for new windows?
The city's Windows and Doors Permit Checklist asks for a copy of the Miami-Dade County Notice of Acceptance for each product, obtained from the point of purchase. Because Fort Lauderdale is in the High-Velocity Hurricane Zone, the approval must cover each opening's size and design pressure.
I live in Sailboat Bend. What do I need before the permit?
A Certificate of Appropriateness. Any change to the outside look of a designated historic property needs one. Start at the Urban Design and Planning counter. Matching replacements can be approved by the Historic Preservation Planner; other changes go to the monthly Historic Preservation Board. Then the permit goes to the Building Division.
My condo tower is on Galt Ocean Mile. What is different?
Get the association's written approval and window spec first. For buildings 30 feet or taller, Broward rules require a signed and sealed site-specific design by a Florida engineer or architect showing every opening and its design pressure. Generic wind charts alone are not accepted for taller buildings.
How do I schedule a window inspection in Fort Lauderdale?
Call DSD Customer Service at 954-828-6520, option 1, Monday to Friday, 8:00 am to 3:30 pm. If your contract is over $5,000, a copy of the recorded Notice of Commencement must be on file with the permit office before the first inspection, so record it before installation day.
Can you help with the Fort Lauderdale permit?
Yes. Permit coordination is available for qualifying projects. Our team manages the required documentation, engineering coordination and submission process from start to finish. Call or text (754) 707-3281 with your Fort Lauderdale address and opening sizes to begin.
Related
Replacing windows in Fort Lauderdale? We coordinate your complete installation from measurement to final inspection.
Call (754) 707-3281 or request an estimate.
Sources: City of Fort Lauderdale – LauderBuild · City of Fort Lauderdale Windows and Doors Permit Checklist · Broward County BORA Formal Interpretation #24 and Fenestration Voluntary Wind Load Chart · FBC Section 1620.2 wind velocity tables (FIU Facilities) · Florida Building Code (overview) · City of Palm Bay – FBC 8th Edition effective date · Florida Statutes s. 713.135 (Notice of Commencement) · Florida Statutes s. 553.899 (milestone inspections) · Broward County 40 Year Safety Inspection FAQ · U.S. Census ACS 2024 1-year via Census Reporter · City of Fort Lauderdale – Historic Districts · City of Fort Lauderdale – Certificate of Appropriateness · Sailboat Bend Historic District survey update · City of Fort Lauderdale – Community Rating System · City of Fort Lauderdale – Flood Zone Designations · Visit Lauderdale – Venice of America · NWS Miami – Hurricane Wilma · Christian Science Monitor, Oct 25, 2005 · NWS Miami – Hurricane Irma · City of Fort Lauderdale notice – Code Sec. 18-9(a) · Fort Lauderdale neighborhoods · Fort Lauderdale ZIP codes
Related pages
Impact windows in Fort Lauderdale: local rules and installation